All-brand parts workspace

Fixes the plastic tabs on the A Pillar that usually break when trying to remove the trim for upgrades like UHF installs

Fits Discovery · 1

Replacement flexible cap for the windshield-washer fluid reservoir filler neck on the Ford Focus MK3 1.5 TDCi, covering the 2011–2018 third-generation application. It restores the removable cover over the washer-fluid tank opening; TPU is specified for the flexible printed part.

Fits Focus · Third generation

Two-piece phone-mount assembly for the large center console in 2020-and-newer Ford Transit vans. The VHB-tape mount base supports a compatible ball-head phone holder, while the removable tray provides a cleanable storage surface and access to small objects. The holder can be adjusted toward the driver or passenger, rotated between portrait and landscape, and used without screws; the source specifies support for phones up to 3.5 inches wide.

Fits Transit · Fifth generation

Replacement passenger-seat recliner handle for the 2006 Ford Explorer, fitting the seat-back recliner mechanism. It restores the lever used to adjust the seat-back angle; one current source geometry is included. Verify fit and operation before regular use.

Fits Explorer · Fourth generation

Replacement bushing for the manual-transmission shifter reverse-lockout knob in the 1968 Ford Mustang application. The longer, thicker profile replaces worn stock bushings to improve fit, smooth operation, and durability. Nylon is the documented material; verify fit and operation before use.

Fits Mustang · First generation

Replacement rear boot/parcel-shelf bracket that clips the cargo shelf in place near the rear seats. Intended for the Ford Focus third-generation hatchback fitment represented by generation 424 (2011–2018). Replaces a broken stock bracket as a direct replacement for the failed bracket.

Fits Focus · Third generation

Reinforced load-bearing insert for the vehicle's OEM jack recess and lift point. It increases contact area for a workshop jack or lift adapter and uses structural ribs to resist shear. Recommended printing uses PETG with 100% infill and four perimeters; ABS/ASA are alternatives. Verify flush fit and inspect the print before applying a full load.

Fits Fusion · North American second generation · Mondeo · Fourth generation

Driver-side replacement clip for the mirror-mounted puddle light/lamp on 2015–2023 Mustang vehicles. It restores retention after the original clip breaks; installation involves trimming the remaining original clip, test-fitting the replacement, and optionally securing it with adhesive or epoxy. One driver-side component is included; no passenger-side version is provided.

Fits Mustang · Sixth generation

Air intake grille. For Defenders equipped with a 300 Tdi, Td5 or Puma motor.

Fits Defender · 300 Tdi · Defender · Td5 · Defender · Puma

Ashtray-slot phone holder for the pre-Puma dashboard.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Simple light guards for Land Rover Defender, just attache them with the original screws.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Defender wing grills, need drilling.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Keep snow, ice, and leaves out of your heater intake with this Snow Cowl. The heater intake cover fits Left Hand Drive Defenders (this goes on the Right Hand Wing).

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Land Rover Defender Internal Door Handle

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

This is a defender door's lock escutcheon

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Land Rover Discovery 2 window and heating switch cover. You need to print 4 pins.

Fits Discovery · 1 · Discovery · 2